bigdemo.blogg.se

1. #Change accounting code for sharp 4070 in design on mac software license
2. #Change accounting code for sharp 4070 in design on mac install

IF YOU DOWNLOAD, INSTALL OR USE THE SOFTWARE, YOU AGREE TO BE LEGALLY BOUND BY THE FOLLOWING TERMS AND CONDITIONS WHICH SHALL ALSO APPLY TO ANY UPGRADES AND UPDATES TO THE SOFTWARE MADE AVALABLE BY XEROX UNLESS THEY ARE PROVIDED UNDER SEPARATE TERMS.

#Change accounting code for sharp 4070 in design on mac software license

IMPORTANT PLEASE READ CAREFULLY BEFORE USING THIS PRODUCT: THIS SOFTWARE LICENSE AGREEMENT ("Agreement") CONTAINS THE LICENSE TERMS AND CONDITIONS FOR THE XEROX SOFTWARE AND RELATED DOCUMENTATION (collectively "Software"). DocuShare Enterprise Content Management.(2 ) The relief valve setting shall not exceed the maximum allowable working pressure of the system. (See § 52.01-3 of this subchapter for definitions.) Relief valves are required at pump discharges except for centrifugal pumps so designed and applied that a pressure in excess of the maximum allowable working pressure for the system cannot be developed. (1 ) Every system which may be exposed to pressures higher than the system's maximum allowable working pressure shall be safeguarded by appropriate relief devices. (2 ) Where the maximum allowable working pressure of a system component, such as a valve or a fitting, is less than that computed for the pipe or tubing, the system pressure shall be limited to the lowest of the component maximum allowable working pressures. (1 ) The maximum allowable working pressure of a piping system must not be greater than the internal design pressure defined in 104.1.2 of ASME B31.1 (incorporated by reference see 46 CFR 56.01-2). Refer to subpart 56.15 for design requirements for fittings. Expansion joints, slip joints, rotary joints, quick disconnect couplings, etc., are referred to as special purpose fittings, and may be subject to such special design and testing requirements as prescribed by the Commandant. Thermometer wells and other similar fittings which form part of the pressure barrier of any system are included under this heading. This includes piping system components whose function is to join branches of the system (such as tees, wyes, elbows, unions, bushings, etc.) which are referred to as pipe joining fittings, as well as components which operate on the fluid contained in the system (such as traps, drains, strainers, separators, filters, meters, etc.), which are referred to as “fluid conditioner” fittings. The word fitting and the phrase fittings and appurtenances within the meaning of the regulations in this subchapter refer to pressure containing piping system components other than valves and pipe. Table 56.04-2 - Pressure Piping Classification Service (viii) (b) When a section or paragraph of the regulations in this part relates to material in ASME B31.1, the relationship with ASME B31.1 will appear immediately after the heading of the section or at the beginning of the paragraph as follows: Table 56.01-5(a) - Limitations and Modifications in the Adoption of ASME B31.1 for Pressure and Power Piping Section or paragraph in ASME B31.1 and disposition Initial service leak test (reproduces 137.7). Preparation for testing (reproduces 137.2). Pressure testing of nonstandard piping system components. Heat treatment of bends and formed components. Piping for instruments, control, and sampling (modifies 122.3).įixed oxygen-acetylene distribution piping.Īcceptable materials and specifications (replaces 123 and Table 126.1 in ASME B31.1). Overboard discharges and shell connections. Metallic expansion joints (replaces 119.5.1).ĭesign Requirements Pertaining to Specific Systemsīilge piping and pumps, alternative requirements. Nonmetallic expansion joints (replaces 119.5.1). Pipe stress calculations (replaces 119.7). Selection and Limitations of Piping Jointsįlared, flareless, and compression fittings.įlexible pipe couplings of the compression or slip-on type. Pipe Flanges, Blanks, Flange Facings, Gaskets, and Bolting Selection and limitations of piping components (replaces 105 through 108).

Piping classification according to service.ĭesign conditions and criteria (modifies 101-104.7). Power boilers, external piping and appurtenances (Replaces 100.1.1, 100.1.2, 122.1, 132 and 133).Īdoption of ASME B31.1 for power piping, and other standards.